Metal Finishing

You are here: Home » Services » Metal Finishing

Boval Engineering has the facilities to offer a complete product finish service.

 

Boval Engineeing’s metal finishing services include sand blasting, powder coating, wet spray, linishing and pickling & passivation. By combining the sandblasting services with metal powder coating, wet spray and linishing, Boval Engineering can provide high quality finishes all in the one location.

 

Powder Coating

Boval Engineering (trading under All Metals Powder Coating) are the Powder Coating Specialists. All Metals Powder Coating’s experienced staff are capable of coating a variety of products made from aluminium, brass, copper, steel, galvanised steel and stainless steel. All Metals Powder Coating stock a wide variety of colours, textures and gloss levels.

 

All Metals Powder Coating’s efficient, conveyorised powder coating plant with online four stage iron phosphate pre treatment process and cure oven services the whole of Australia. All Metals Powder Coating can powder coat products up to 770mm wide, 1600mm high and 2700mm long. The plant is ideal for both short and long runs.

 

In addition, All Metals Powder Coating have a batch plant with capacity up to 1700mm wide, 2700mm high and 3200mm long.

 

  • Fully conveyorised powder coating system
  • Hot phosphate pre-wash
  • All colours
  • Superior finish
  • Phosphate coatings
  • Powder adhesion
  • Fluidised bed technique

Metal Abrasive Blasting

Abrasive blasting or sandblasting metal finishing processes work on a variety of surfaces including metal, wood, concrete, brick and stone.

 

  • Advanced cleaning process
  • Removal of old paint, casting material or coatings
  • Removal of stubborn dirt, grease, rust, scale or water deposits
  • Preserve metal surfaces
  • The capacity of the abrasive blaster facility at Boval Engineering is 1.8m wide x 1.9m height x 3m depth

Wet Spray

Boval Engineering offers wet spraying, the metal finishing process is ideal for items which cannot tolerate the high temperatures involved in the powder coating process. The finish achieved from the wet spray process is very similar to that of powder coating; durable coating in a wide variety of colours, textures and gloss levels.

 

Boval Engineering have a large wet spray area which allows for small to large with dimensions; width 4m, depth 3m, height 2.4m.

 

  • Primers
  • Two pack polyurethane
  • Anti-corrosion resistant coating
  • Air dry single pack coatings
  • Water based paints and coatings
  • Two pack epoxy
  • Three coat systems

Linishing

Boval Engineering offers linishing to their customers as part of the metal finishing process. Linishing is a process commonly used to produce a fine finish on sheet metal or plate components. A linishing belt is passed back and forth over the sheet until the surface has been cleaned up completely.

 

Linishing is often preferable over grinding as uneven surfaces can be finished off with minimal material removal. Also less heat is usually generated during the process often reducing the need for the use of a coolant.

 

Features:

  • #2 Finish
  • Hand Finish or Machine Finish
  • All Metal Types

Pickling & Passivation

Boval Engineering offer their customers pickling and passivation for stainless steel products. These chemical treatments are required if there is corrosion of the stainless steel due to contamination of the surface. Pickling and passivation chemical treatments are applied to the stainless steel surface and aim to remove the contaminants that are causing the corrosion.

 

Pickling is the removal of any high temperature scale and any adjacent low chromium layer of metal from the surface of stainless steel by chemical means.

 

Passivation is the treatment of the surface of stainless steels, often with acid solutions (or pastes), to remove contaminants and promote the formation of the passive film on a freshly created surface.

 

For cleaning of stainless steel welds Boval Engineering also offers TIG Brush cleaning. This metal finishing process cleans welds and restores stainless steel surfaces.  TIG Brush cleaning uses a proprietary electro-chemical process, combining low-toxicity liquids to produce superior results.

Powder Coating

Metal Abrasive Blasting

Wet Spray

Linishing

Pickling & Passivation

Contact Boval for a Metal Finishing Quote